Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is a cutting-edge anti-theft system that uses advanced technology to prevent car theft. autowatch ghost immobiliser cost hidden device is not detected by thieves and only starts your engine when a PIN number or app is entered.
It connects to the CAN data network in your vehicle and is weatherproof. It also comes with a service/valet mode, which allows you to start your car for a short period when it's in the garage for servicing or cleaning.
Easy to install
The Ghost immobiliser shields your car from theft of keys, cloning and hacking. It uses a unique PIN code system that is incorporated into the ECU of your vehicle which makes it extremely difficult for thieves to identify or tamper with. Contrary to traditional immobilisers it does not require any special keys or sensors, and is completely hidden from view without any LED indicators or signals to give away its presence. It's also less expensive than replacing an ECU or installing a key fob. It can even lower your insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's directions carefully. This will ensure that the device functions correctly and effectively. After the installation is completed check the system by entering the PIN code, then turning on the engine. Regular testing will enable you to detect any issues in the early stages.
Before you begin the installation, ensure the position of the CAN H and L wires. They are crucial to power the immobiliser, so it is vital that they are connected properly. It is also recommended to label the wires so that it makes it easier to locate them during the installation process. Once you've identified the location of these wires, connect them to a permanent 12V power source and the grounding point. Use the fuse tap to safeguard the connections against damage or short-circuits.
After connecting the wires, neaten the wiring with cable ties to prevent alteration. You can also cover the connections using insulation tape or heat-shrink tubing. This will shield the device from electrical shorts and extend its lifespan. It is a good idea to test your Ghost 2 immobiliser once the wiring is secure.
The Ghost 2 immobiliser offers a service mode in situations where you may have to give your vehicle away like when it is being repaired or valet parked. This disables the PIN sequence temporarily. To activate this feature, simply press the brake pedal while holding the accelerator, a number of times that is equal to the first number of the emergency code. The system will go into service mode. This is confirmed by flashing 5 times the indicator signal.
Change PIN codes with ease
Ghost 2 immobilisers are an excellent method of protecting your vehicle from theft. It is concealed inside the vehicle, and can only be accessed through a specific code. The device communicates with the vehicle ECU via its data bus. It does not rely on radio frequency signals as traditional alarm systems or aftermarket Thatcham immobilisers do. This makes it difficult for thieves to detect the click of an immobiliser relay or to install new key fobs. The control unit is concealed in the wiring of the vehicle or dashboard, and cannot be physically tampered to reset the system.
The ghost 2 immobiliser connects to the vehicle's CAN Data network. It makes use of buttons on the door panels, the steering wheel and centre console, to create a customized sequence of up to twenty button presses, which must be entered to start the engine, just as a PIN. This next-generation system doesn't require any cutting of wires during installation and is fully reprogrammable at any time. You can even set your vehicle in Valet or Service mode to allow it to start temporarily while you are giving it to a mechanic to work.
The application can also be used to block your PIN code if you've lost your keys or change it. This feature is especially useful if you've given your car to another person for parking or valet services. It will stop them from starting it and driving it off without your consent. It's also unnoticeable to professional thieves because it does not use any circuit cuts or radio frequencies.
Another excellent feature of the ghost 2 immobiliser is its capability to prevent thefts of relays. Relay theft is among the most frequent methods of car theft. Criminals can hack your car's diagnostic ports, and then alter the signal transmitted by the car's ECU to fool it into thinking that the car's key is valid and present. The traditional immobiliser can be manipulated in this way, but with the ghost 2 immobiliser, the signal is blocked by the immobiliser before it reaches the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that safeguards your car from key-cloning, hacking, and key theft. It connects to the CAN data network of your vehicle and requires an PIN code to start the engine. It also stops thieves from using signal spoofing and device spoofing, which are both common methods used to steal vehicles.
The system is easy to use and works like an ordinary auto alarm. After installing it, you are able to create a unique PIN sequence that is up to 20 characters long, which will have to be entered before the vehicle is started. This will stop the vehicle from being taken even if your keys are stolen. If you wish to disable the system it is possible to do this by using an app on your smartphone.
Contrary to other systems it is completely silent and does not emit radio frequency signals. It is a weatherproof, discrete device that can be positioned anywhere inside your vehicle. It can be concealed under the dashboard, door panels or the steering wheel. It communicates through the CAN data loop with your ECU and is not affected by the diagnostic tools used by thieves to find security systems. It is not affected by jamming devices which can spoof codes.
It is a concealed installation that doesn't require any cutting of wires or modifications to the car and can be used as an anti-theft system for any vehicle. The technology has been proven to be effective and in compliance with TASSA standards. Ghost is a great solution for classic, sports and prestige cars. It can be used to safeguard vehicles that are being let out on websites like Turo.
The Autowatch Ghost 2 is the next generation in vehicle immobilisers. The system is unnoticeable to thieves and blocks them from starting your car without a PIN or are authorised by the app. It also does not emit radio frequencies or other signals that could be detected by scanners. Installation is fast and simple. The app is simple to navigate and offers a user-friendly interface which makes it simple to install and use. It also includes a GPS tracker that can assist police find the vehicle and locate it.
Easy to reset
It is possible to protect your vehicle from theft using an immobiliser ghost 2. It integrates into your vehicle's ECU, creating a barrier that thieves cannot breach without the correct pin. It's also TASSA-certified that means it's acknowledged by insurance companies. It's a powerful tool to stop car theft and could save you a significant amount of money over the long term.
The Ghost system, unlike traditional alarm/immobilisers which require cutting circuits, is directly connected to the vehicle's CAN data network. It operates through the buttons on your dashboard and steering wheel. You can create a unique PIN that can be up to 20 presses in length. This PIN has to be entered before the engine can start the same way as the credit card PIN. The Ghost system is undetectable to thieves and has no indicators that signal its presence, which makes it the most efficient aftermarket CAN bus immobiliser on the market currently.
The Ghost system also has a benefit: it does not transmit radio frequency signals. This means it cannot be scanned by thieves or intercepted. This is a deterrent to key attacks that are cloned and relay attacks, as well as the usual method of hacking into a car's computer system using its CAN bus searching for signals. The Ghost system is designed in a way that it is able to be hidden inside your vehicle. There aren't any lights, or other indicators to indicate its presence.
The system has a Transport Mode which disables the Ghost System. This is useful in situations where you need to temporarily deactivate Ghost for instance, when you're transporting or maintaining your vehicle. However, this mode is not as effective as Service Mode, as it does not disable the system if your vehicle is traveling over 31 mph for more than 15 minutes.
You will require the emergency code provided by your installer to reset your Ghost 2 immobiliser. It is usually hidden under an area for scratch-offs on the card included with the installation. This emergency code should be secured and stored in a secure location, such as an at-home wallet.